Component Solution Services REC02F Instrukcja Obsługi Strona 117
- Strona / 142
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Ultraview 1030/1050 Monitors — Service Manual
5-29
Troubleshooting
6 If the loopback test does not pass, replace the CO
2
/SDLC PCBA.
7 If all the voltages are present and the loopback test passes, then the problem is likely in the
Sensor Interface PCBA.
8 Replace the test software (P/N 174-0527-01) in U37 with the original software.
Sensor Fault
• Verify that the flex circuit is not damaged and that it is seated correctly in the connector. The
flex circuit connector is unlocked by pulling the plastic housing away from the PCBA. The flex
circuit should then pull out easily. To re-install, push the flex circuit into the connector until it
bottoms out, approximately 0.29 inches (7 mm).
• Replace the CO
2
sensor.
• Replace the Sensor Interface PCBA.
Non-Spacelabs Medical Sensor Detected
• Replace the CO
2
sensor.
Sensor Temperature Failure
• Replace the CO
2
sensor.
Warm-up Time-out
• Replace the CO
2
sensor.
O2 Zero Rejected
•O
2
sensor and/or cable is plugged into O
2
jack. Unplug the connector.
•O
2
connector does not close when the plug is removed. Jumper TP10 to TP2 of the
CO2/SDLC PCBA and repeat O
2
zero. If it passes, replace the flex circuit.
• If it fails the above test, there is something wrong with the O
2
amplifier or A to D converter.
Replace the CO
2
/SDLC PCBA.
O2 Span Rejected
• Refer to O2 Reads Low on page 5-27.
100% O2 Span Failed
• Refer to O2 Reads Low on page 5-27.
O2 Span Required
• Perform room and 100% O
2
spans (this is required whenever an O
2
sensor is changed or an
O
2
ZERO calibration is performed).
- Ultraview 1
- 1030 and 1
- Ultraview 1050 Monitors 1
- Table of Contents 3
- Introduction 5
- Monitor Hardware Options 6
- Unpacking 9
- Batteries 10
- Nickel Metal Hydride (NiMH) 11
- Battery Use 11
- Sealed Lead Acid (SLA) 11
- Caution: 12
- Assembly 13
- Back Panel Connections 14
- Power-ON Test 16
- Cables and Adapters 18
- Maximum Cable Lengths 18
- Software Configuration 19
- CONFIGURABLE 22
- ALARM TONES 22
- CONTINUOUS 22
- Keyboard Menu 23
- Biomed Setup Keys 24
- TCP/IP Setup Key 25
- BED NAME Key 25
- NODE DIRECTORY Key 25
- RECORDER SETUP Key 26
- RECORDER NAMES Key 27
- SELECT RECORDERS Key 27
- Select option to change 28
- Select recording type 28
- Select beds/subnets 28
- ALARM SETUP Key 29
- HIGH MEDIUM 30
- USER ACCESS Key 31
- TONE CONFIGURATION Menu Tree 31
- SERVICE FUNCTIONS Menu 32
- STATISTICS 33
- SITE SURVEY Key 34
- PRINT Key 34
- CHANGE PASSWORD Key 34
- RESET MONITOR Key 34
- Updating Flash PROM 35
- Network Configuration 35
- Ethernet Installation 36
- Ethernet Removal 36
- Module Tests 36
- 90310 Front Panel 37
- DC Power Supply 42
- Parameter Module 42
- Optional Capnography 42
- 90367/90369 Monitor 43
- CPU PCBA 44
- Main CPU 45
- MPC860-PCI Bridge 45
- Ethernet 46
- PMC Connector 46
- ISA Bridge 46
- Wireless LAN Card 47
- Keyboard/Mouse Interface 47
- ISA I/O Buffers 47
- SDLC Interface 48
- Touchscreen Circuitry 48
- Nurse Alarm Output 48
- Clock Distribution 48
- Hardware Reset 49
- Software Reset 50
- Power Failure Operation 50
- Hard Reset Configuration Word 50
- Interrupts 50
- Power Supply System 52
- Battery Chargers 54
- Normal Operation Overview 56
- EMI Reduction 56
- Boot Sequence Overview 56
- Touchscreen PCBA 58
- 26 gnd Input 59
- I/O Bay PCBA 60
- Recorder Interface PCBA 62
- ICB (Interconnect PCBA) 63
- Maintenance 65
- Fan Filter 66
- Mechanical Inspection 67
- Electrical Safety Testing 67
- Definitions 68
- Ground Resistance 69
- Chassis Leakage Current Tests 69
- Preventive Maintenance 70
- Functional Checks 70
- Capnography 72
- Part Replacement Procedures 74
- Replacing the Main PCBA 75
- Removing the Chassis Assembly 76
- Removing the Door 80
- Removing the Bezel 82
- Removing the I/O Bay PCBA 84
- Removing the CO 86
- PCBAs for Option G 86
- PCBAs for Option H 88
- System Startup 90
- Boot Menu 91
- Power ON Diagnostics 93
- Extended Diagnostics 93
- Diagnostic Menus 94
- MEMORY MENU 96
- Diagnostic LED 98
- Error Log 99
- Troubleshooting 101
- System Troubleshooting 103
- Touchscreen Troubleshooting 104
- Ethernet Troubleshooting 105
- Module Slot Troubleshooting 105
- SDLC Output Troubleshooting 105
- Battery Troubleshooting 107
- Recorder Troubleshooting 108
- Capnography Troubleshooting 113
- Does Not Display 114
- Reads Low 115
- Check Reads Low 115
- Problem Messages 116
- Contents 119
- Overview 119
- Field Replaceable Parts List 119
- Drawings 123
- Appendix A — Glossary 125
- Appendix B — Electromagnetic 131
- Compatibility 131
- Electromagnetic Immunity 132
- Interference 134
- Mitigation 134
- Appendix C — Symbols 135
- 12,200 m 137
- Approved 140
- ETL Laboratory Approved 140
Powiązane produkty i podręczniki dla Cyfrowe rejestratory wideo (DVR) Component Solution Services REC02F
(41 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji